| Model Series | MTX-RYZ1 |
| Part Number | MTX-RYZ1-884500A1 | MTX-RYZ1-884502A1 (Onboard TPM 2.0) |
| Form Factor | Mini ITX (170 x 170mm) |
| Processor | AMD Ryzen™ 7 PRO 8845HS, 8 Cores 16 Threads, 45W TDP, Formerly Hawk Point |
| AI | Overall TOPS Up to 38 TOPS |
| Memory | 2 x Dual Channel Non-ECC DDR5-5600 SODIMM up to 96GB |
| Graphics | AMD Radeon™ 780M (Supports 4 Display), RDNA3 Core Architecture, Shared Memory |
| Audio | Realtek ALC897 HD Audio with 3W Amplifier |
| LAN | 2 x Intel I226-V 2.5GbE |
| Storage | 2 x SATA3 6Gb/s 2 x M.2 2242/2280 (PCIe 4.0 x4 NVMe, M-key) Supports NVMe RAID 0/1 |
| Super IO | FINTEK F81966D |
| TPM | AMD fTPM 2.0 Firmware | AMD fTPM 2.0 Firmware Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
1 12V ~ 28V DC-in Locking Jack
4 DP 2.1 (3840 x 2160 @ 120Hz)
2 RJ45 2.5GbE LAN (10/100/1000/2500)
4 USB 3.2 Gen 1x1 (5 Gb/s)
2 Serial Ports (2 * RS232/422/485)
1 3.5mm Line-in Jack
1 3.5mm Line-out Jack
1 3.5mm MIC-in Jack

|
| Onboard I/O Connectors |
1 PCIe 4.0 x8 Slot
2 SATA3 6Gb/s Connector
2 M.2 M-Key, 2242/2280 (PCIe 4.0 x4 NVMe)
1 M.2 E-key, 2230 (USB2.0 and PCIe 4.0 x1)
3 USB Pin Headers for 6 additional USB 2.0 Ports
4 Serial Headers (4 * RS232)
1 eDP 1.5 connector (Max 3840 x 2160 @ 120Hz)
1 24-bits Dual Channel LVDS (Max 2560 x 1600 @ 60Hz)
1 16 bit GPIO Header
1 AT/ATX Mode Jumper
1 9-pin Front Audio Header
1 5-pin SMBUS Header
2 Fan Header
1 4-pin Alternate Power-in Connector
|
| Power for MTX-RYZ1 |
External Power Supply – the board can be powered with a +12V ~ +28V external power supply though a DC connector on the back panel. The rear +12V ~ +28V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm.
Internal Power Supply – the board can alternatively be powered via the internal +12V ~ +28V DC 2 x 2 power connector, where pins 3 and 4 are +12V ~ +28V (±5%) DC and pins 1 and 2 are GND. The connector used is Molex Micro-Fit (3mm pitch), right-angled, 4-pos/dual row (2x2).
Caution: There is no isolation circuitry between the external +12V ~ +28V DC jack and the internal 2 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V ~ +28V DC jack is covered if the internal 2 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Edge Computing
√ Digital Signage
√ Industrial PCs
√ Factory Automation
√ Public Sector
√ Digital Security
√ Surveillance Application
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 70°C
Humidity : 10% ~ 90% RH @40°C (non-condensing)
|