FAQs & Troubleshooting

Find answers to common technical questions and compatibility guidelines for Jetway motherboards and systems.

Frequently Asked Questions

MEMORY
Why do you only provide an initial factory test report instead of a continually updated Memory Support List?

Rapid market fluctuations and supply chain constraints make it impossible to maintain a consistently accurate and published list.

Why might a validated memory part number change its internal configuration later?

Due to ongoing IC shortages, memory vendors frequently substitute internal DRAM chips without updating the retail model name or part number.

What type of memory do you recommend purchasing?

We strongly recommend Industrial Grade memory. These modules typically offer a fixed BOM (Bill of Materials), which effectively prevents unexpected compatibility issues caused by unannounced component revisions.

What is the maximum DDR5 memory frequency supported by Intel 12th, 13th, and 14th GEN Processors?

Please refer to the charts below from Intel.

Intel 12th GEN All Processors
Memory Type UDIMM SODIMM
DIMM per Channel Speed 1DPC:
4800
2DPC:
4400 (1DIMM)
4000 (2DIMM 1R)
3600 (2DIMM 2R)
1DPC:
4800
Intel 13th GEN Core i9, i7 Series
Memory Type UDIMM SODIMM
DIMM per Channel Speed 1DPC:
5600
2DPC:
4400 (1DIMM)
4000 (2DIMM 1R)
3600 (2DIMM 2R)
1DPC:
5600
Intel 13th GEN Core i5, i3 Series
Memory Type UDIMM SODIMM
DIMM per Channel Speed 1DPC:
4800
2DPC:
4400 (1DIMM)
4000 (2DIMM 1R)
3600 (2DIMM 2R)
1DPC:
4800
Intel 14th GEN Core i9, i7, i5K, i5-14600 Series
Memory Type UDIMM SODIMM
DIMM per Channel Speed 1DPC:
5600
2DPC:
4400 (1DIMM)
4000 (2DIMM 1R)
3600 (2DIMM 2R)
1DPC:
5600
Intel 14th GEN Core i5-14500, i5-14400, i3 Series
Memory Type UDIMM SODIMM
DIMM per Channel Speed 1DPC:
4800
2DPC:
4400 (1DIMM)
4000 (2DIMM 1R)
3600 (2DIMM 2R)
1DPC:
4800
BIOS
How to set up Intel PTT? (Example model: MI225-Q670)
  1. Press [Del] during boot-up to enter UEFI BIOS setup.
  2. Go to Advanced > PCH-FW Configuration and set TPM Device Selection to PTT.
  3. Go to Advanced > Trusted Computing and set Security Device Supportto Enabled.
  4. Go to Save & Exit and Save Changes & Reset.
Do all Jetway motherboards have Auto Restart After Power Loss feature in the BIOS?

Yes, please go to BIOS > Chipset > PCH-IO Config > System State After Power Failure > set to Always On. Some earlier boards that are ErP compliant, first need to disable the ErP in the BIOS, then the Power Status after Power Failure option will show. Alternatively, configure the AT mode jumper if supported.

How to Clear the BIOS Password (All Models)

Refer to the motherboard manual for the "Clear CMOS" section, then momentarily bridge the two pins.

STORAGE
How to set up a RAID array using M.2 and SATA drives? (Example model: MI215-Q670)
  1. Press [Del] during boot-up to enter BIOS setup.
  2. Go to Chipset > System Agent Configuration and set VMD Configuration to Enabled.
  3. Go to Advanced > Intel(R) Rapid Storage Technology.
  4. Select Create RAID Volume.
  5. Choose RAID 0 or RAID 1.
  6. Select Create Volume to finish.
How to set up Intel(R) RAID? (Example model: NF697-Q170)
  1. Press [Del] during boot-up to enter BIOS setup.
  2. Go to Advanced > SATA Configuration > SATA Mode Selection and set RAID and Save.
  3. Press "Ctrl + I" after reboot to enter Intel(R) Rapid Storage Technology - Option ROM.
  4. Select Create RAID Volume.
  5. Choose RAID 0 or RAID 1.
  6. Press [ESC] - Exit to finish.
How to set up Intel VMD? (Example model: MI215-Q670 and NVMe SSD)
  1. Press [Del] during boot-up to enter BIOS setup.
  2. Go to Chipset > System Agent (SA) Configuration > VMD setup menu and set VMD Contoller to Enabled.
  3. Go to Advanced > Intel(R) Rapid Storage Technology.
  4. Select Create RAID Volume.
  5. Choose RAID 0 or RAID 1.
  6. Select Create Volume to finish.
Why can't I fully use a hard drive greater than 2TB? (For earlier legacy models)

In order for an operating system to fully support storage devices that have capacities that exceed 2 terabytes (2TB, or 2 trillion bytes), the device must be initialized by using the GUID partition table (GPT) partitioning scheme. This scheme supports addressing of the full range of storage capacity. If you intend to start the computer from one of these large disks, your motherboard's base firmware interface must use the UEFI (Unified Extensible Firmware Interface) BIOS.

Troubleshooting Guide

HARDWARE & BOOT ISSUES
System fails to power on (No POST, no display, no beep codes)

Troubleshooting Steps & Suggestions:

  • Verify the DC power adapter output voltage.
  • Inspect and clean the AT/ATX power supply connectors.
  • Test with a known-good power adapter.
  • Clear CMOS jumper and try again.
RMA Recommendation: Recommended if the system remains completely unresponsive.
System fails to boot with continuous beep codes

Troubleshooting Steps & Suggestions:

  • Verify memory installation and inspect slots for oxidation.
  • Isolate the issue by testing one memory module at a time.
  • Clean DIMM slots and memory contact pins.
  • Try a different memory module to rule out compatibility issues.
RMA Recommendation: Recommended if the issue persists across different memory modules.
System boots but outputs no display signal

Troubleshooting Steps & Suggestions:

  • Verify display cables (HDMI/DP/VGA) and monitor functionality.
  • Try a different monitor to rule out compatibility issues.
  • If utilizing a discrete GPU, reseat the card or test in an alternate PCIe slot.
RMA Recommendation: Conditional, pending isolation of the motherboard display output.
System boots but fails to detect SSD/SATA storage devices

Troubleshooting Steps & Suggestions:

  • Inspect and reseat all SATA data and power cables.
  • Cross-test with alternate drives and SATA ports.
  • Clean SATA port contacts on the motherboard.
RMA Recommendation: Recommended if multiple SATA ports consistently fail to detect drives.
Unable to enter BIOS menu or execute BIOS updates

Troubleshooting Steps & Suggestions:

  • Perform a CMOS reset (remove the RTC battery for 5+ minutes).
  • Test the keyboard on a different USB port.
  • Attempt recovery via an external BIOS flashing tool if applicable.
RMA Recommendation: Recommended if the BIOS chip remains unresponsive.
System exhibits random freezing, unexpected reboots, or visual artifacts

Troubleshooting Steps & Suggestions:

  • Verify proper contact between the CPU and heatsink.
  • Inspect the motherboard for foreign objects or thermal paste spillage causing shorts.
  • Perform a clean OS installation to rule out potential compatibility issues.
RMA Recommendation: Conditional, recommended if hardware failure is confirmed after ruling out thermal, OS, and driver issues.
Odor of burning electronics or abnormal component overheating

Troubleshooting Steps & Suggestions:

  • Disconnect power immediately and do not attempt to turn it on.
  • Perform a visual inspection for burnt ICs, inductors, or MOSFETs.
  • Document any visible physical damage with clear photographs.
RMA Recommendation: Strongly recommended (Please attach photos when submitting the ticket).
BIOS settings reset or system clock loses time after power cycling

Troubleshooting Steps & Suggestions:

  • Measure the CMOS battery voltage to determine if it is depleted.
  • Replace the existing battery with a new CR2032 coin cell.
  • Ensure the battery socket contacts are clean and properly tensioned.
RMA Recommendation: Recommended if the issue persists after installing a fresh battery.
Cooling fan fails to spin or exhibits erratic RPM behavior

Troubleshooting Steps & Suggestions:

  • Verify the fan is securely connected to the designated motherboard header.
  • Test the fan using an external power source or alternate header.
  • Check BIOS settings for misconfigured SmartFan control profiles.
RMA Recommendation: Recommended if the motherboard fan header is confirmed dead.