| Model Series | MF06 |
| Part Number | MF06-03 | MF06-07 |
| Form Factor | 3.5" SBC (148 x 102mm) |
| Processor | Intel® Celeron J3455 Quad Core 1.50 GHz - 2.30 GHz, 10W TDP (Formerly Apollo Lake) * Ships with flat silver aluminum heatsink for direct attaching to a surface |
| Memory | 1 x 204-pin DDR3L-1866 SO-DIMM up to 8GB (1.35V required) |
| Graphics | Intel HD Graphics 500, 250MHz - 750MHz |
| Audio | Realtek ALC897 or ALC888 HD Audio |
| LAN | 1 x Intel I225-LM PCIe 2.5GbE 1 x Intel I211-AT PCIe Gigabit LAN |
| Storage | 1 x 32GB eMMC 1 x SATA3 6Gb/s 1 x M.2 (SATA, M-key, 2242/2280) |
| Super IO | FINTEK F81962D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware | Intel fTPM 2.0 (PTT) Trusted Computing Firmware Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
1 3.5mm Line-out & MIC-in Audio Jack
2 HDMI 1.4b (3840 * 2160 @ 30Hz)
3 USB 3.2 Gen 1 (5 Gb/s)
3 USB 2.0
1 RJ45 LAN (10/100/1000/2500)
1 RJ45 LAN (10/100/1000)
1 +9V – 36V 2.5mm Diameter DC Power Jack

|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2242/2280 (SATA only)
1 M.2 E-key, 2230 (USB and PCIe for WiFi)
1 M.2 B-key, 3042 (USB and PCIe) with Micro SIM Slot
2 Serial Headers (1 * RS232, 1 * RS232/422/485)
2 USB Pin Headers for 4 additional USB 2.0 Ports
1 40-pin eDP (4096 * 2304 @ 60Hz)
1 24-bit Dual Channel LVDS/Inverter (1920 * 1080 @ 60Hz)
1 8 bit GPIO Header
1 4-pin SMBUS Header
1 4-pin Fan Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 2-pin +9-36V Alternate DC-in (Mating plug: JST VHR-2N or TE 1-1123722-2)
|
| Power Supply for MF06 |
External Power Supply – the board can be powered with a +9 - 36V external power supply though a DC connector on the back panel. The rear +9 - 36V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +9 - 36V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +9 - 36V 2-pin power connector, where pin 1 is +9 - 36V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +9 - 36V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +9 - 36V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM/Digital Signage)
√ Digital Security / Surveillance
√ Panel PC
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|