| Model Series | DMTX-ADN1 |
| Part Number | DMTX-ADN1-N9700 | DMTX-ADN1-N9702 (Onboard TPM 2.0) |
| Form Factor | Mini-ITX (170 x 170mm) |
| Processor | Intel® Processor N97, up to 3.60 GHz, 4-Core 4-Thread, 12W TDP (Products formerly Alder Lake-N) |
| Memory | 1 x 262-pin Single Channel DDR5-4800 SO-DIMM up to 16GB Total |
| Graphics | Intel® UHD Graphics Up to 3 Displays |
| Audio | Realtek ALC897 HD Audio, 3W Amplifier |
| LAN | 2 x Realtek® RTL8111H Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s 1 x M.2 (SATA/PCIe 3.0 x2, M-key, 2242 2280 NVMe) 1 x M.2 (SATA, M-key, 2242) |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) | Intel fTPM 2.0 (PTT) Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
1 +12V - 19V 2.5mm Diameter DC Power Jack
1 DP 1.4 (4096 * 2160 @ 60Hz)
1 HDMI 2.0b (4096 * 2160 @ 60Hz)
2 USB 3.2 Gen 1x1 (5 Gb/s)
2 USB 2.0 Port
2 RJ45 LAN (10/100/1000)
1 3.5mm Line-out Jack
1 3.5mm MIC-in Jack

|
| Onboard I/O Connectors |
1 PCIe 3.0 x4 Slot (1 Lane)
1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2242/2280 (SATA/PCIe 3.0 x2 NVMe)
1 M.2 M-Key, 2242 (SATA)
1 M.2 E-key, 2230 (PCIe 3.0 x1/USB 2.0/CNVi for WiFi)
6 Serial Headers (2 * RS232/485, 4 * RS232)
3 USB Pin Headers for 6 additional USB 2.0 Ports
1 30-pin eDP (1920 * 1200 @ 60Hz)
1 24-bit Dual Channel LVDS/Inverter (1920 * 1080 @ 60Hz)
1 8 bit GPIO Header
1 5-pin SMBUS Header
1 9-pin Front Audio Header
1 Chassis Intrusion Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 2-pin +12V – 19V Alternate Power-In (Mating plug: JST VHR-2N or TE 1-1123722-2)
|
| Power Supply for DMTX-ADN1 |
External Power Supply – the board can be powered with a +12V – 19V external power supply though a DC connector on the back panel. The rear +12V – 19V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V – 19V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V – 19V 2-pin power connector. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 connector from the power supply.
Caution: There is no isolation circuitry between the external +12V – 19V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V – 19V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM/Digital Signage)
√ Digital Security / Surveillance
√ Panel PC
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 70°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|